89C51.pdf

(142 KB) Pobierz
AT89C51
Features
• Compatible with MCS-51 ™ Products
• 4K Bytes of In-System Reprogrammable Flash Memory
– Endurance: 1,000 Write/Erase Cycles
• Fully Static Operation: 0 Hz to 24 MHz
• Three-level Program Memory Lock
• 128 x 8-bit Internal RAM
• 32 Programmable I/O Lines
• Two 16-bit Timer/Counters
• Six Interrupt Sources
• Programmable Serial Channel
• Low-power Idle and Power-down Modes
8-bit
Microcontroller
with 4K Bytes
Flash
Description
The AT89C51 is a low-power, high-performance CMOS 8-bit microcomputer with 4K
bytes of Flash programmable and erasable read only memory (PEROM). The device
is manufactured using Atmel’s high-density nonvolatile memory technology and is
compatible with the industry-standard MCS-51 instruction set and pinout. The on-chip
Flash allows the program memory to be reprogrammed in-system or by a conven-
tional nonvolatile memory programmer. By combining a versatile 8-bit CPU with Flash
on a monolithic chip, the Atmel AT89C51 is a powerful microcomputer which provides
a highly-flexible and cost-effective solution to many embedded control applications.
AT8 9C5 1
Pin Configurations
PDIP
Not Recommended
for New Designs.
Use AT89S51.
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
RST
(RXD) P3.0
(TXD) P3.1
(INT0) P3.2
(INT1) P3.3
(T0) P3.4
(T1) P3.5
(WR) P3.6
(RD) P3.7
XTAL2
XTAL1
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
VCC
P0.0 (AD0)
P0.1 (AD1)
P0.2 (AD2)
P0.3 (AD3)
P0.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0.7 (AD7)
EA/VPP
ALE/PROG
PSEN
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
P2.4 (A12)
P2.3 (A11)
P2.2 (A10)
P2.1 (A9)
P2.0 (A8)
PQFP/TQFP
P1.5
P1.6
P1.7
RST
(RXD) P3.0
NC
( TXD ) P3.1
( INT0 ) P3.2
(INT1) P3.3
(T0) P3.4
(T1) P3.5
1
2
3
4
5
6
7
8
9
10
11
33
32
31
30
29
28
27
26
25
24
23
PO.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0 .7 (AD7)
EA/VPP
NC
ALE/P ROG
PSEN
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
PLCC
P1.5
P1.6
P1.7
RST
(RXD) P3.0
NC
(TXD ) P3.1
( INT0 ) P3.2
(INT1) P3.3
(T0) P3.4
(T1) P3.5
7
8
9
10
11
12
13
14
15
16
17
39
38
37
36
35
34
33
32
31
30
29
PO.4 (AD4)
P0.5 (AD5)
P0.6 (AD6)
P0 .7 (AD7)
EA/VPP
NC
ALE/P ROG
PSEN
P2.7 (A15)
P2.6 (A14)
P2.5 (A13)
Rev. 0265G–02/00
1
221378381.023.png 221378381.024.png
 
221378381.025.png
 
221378381.001.png
 
221378381.002.png 221378381.003.png 221378381.004.png 221378381.005.png
 
Block Diagram
P0.0 - P0.7
P2.0 - P2.7
V CC
PORT 0 DRIVERS
PORT 2 DRIVERS
GND
RAM ADDR.
REGISTER
RAM
PORT 0
LATCH
PORT 2
LATCH
FLASH
B
REGISTER
ACC
STACK
POINTER
PROGRAM
ADDRESS
REGISTER
TMP2
TMP1
BUFFER
ALU
PC
INCREMENTER
INTERRUPT, SERIAL PORT,
AND TIMER BLOCKS
PSW
PROGRAM
COUNTER
PSEN
ALE/PROG
EA / V PP
RST
TIMING
AND
CONTROL
INSTRUCTION
REGISTER
DPTR
PORT 1
LATCH
PORT 3
LATCH
OSC
PORT 1 DRIVERS
PORT 3 DRIVERS
P1.0 - P1.7
P3.0 - P3.7
2
AT89C51
221378381.006.png 221378381.007.png 221378381.008.png 221378381.009.png 221378381.010.png 221378381.011.png 221378381.012.png 221378381.013.png 221378381.014.png 221378381.015.png 221378381.016.png 221378381.017.png
AT89C51
The AT89C51 provides the following standard features: 4K
bytes of Flash, 128 bytes of RAM, 32 I/O lines, two 16-bit
timer/counters, a five vector two-level interrupt architecture,
a full duplex serial port, on-chip oscillator and clock cir-
cuitry. In addition, the AT89C51 is designed with static logic
for operation down to zero frequency and supports two
software selectable power saving modes. The Idle Mode
stops the CPU while allowing the RAM, timer/counters,
serial port and interrupt system to continue functioning. The
Power-down Mode saves the RAM contents but freezes
the oscillator disabling all other chip functions until the next
hardware reset.
Port 2 pins that are externally being pulled low will source
current (I IL ) because of the internal pullups.
Port 2 emits the high-order address byte during fetches
from external program memory and during accesses to
external data memory that use 16-bit addresses (MOVX @
DPTR). In this application, it uses strong internal pullups
when emitting 1s. During accesses to external data mem-
ory that use 8-bit addresses (MOVX @ RI), Port 2 emits the
contents of the P2 Special Function Register.
Port 2 also receives the high-order address bits and some
control signals during Flash programming and verification.
Pin Description
Port 3
Port 3 is an 8-bit bi-directional I/O port with internal pullups.
The Port 3 output buffers can sink/source four TTL inputs.
When 1s are written to Port 3 pins they are pulled high by
the internal pullups and can be used as inputs. As inputs,
Port 3 pins that are externally being pulled low will source
current (I IL ) because of the pullups.
Port 3 also serves the functions of various special features
of the AT89C51 as listed below:
VCC
Supply voltage.
GND
Ground.
Port 0
Port 0 is an 8-bit open-drain bi-directional I/O port. As an
output port, each pin can sink eight TTL inputs. When 1s
are written to port 0 pins, the pins can be used as high-
impedance inputs.
Port 0 may also be configured to be the multiplexed low-
order address/data bus during accesses to external pro-
gram and data memory. In this mode P0 has internal
pullups.
Port 0 also receives the code bytes during Flash program-
ming, and outputs the code bytes during program
verification. External pullups are required during program
verification.
Port Pin
Alternate Functions
P3.0
RXD (serial input port)
P3.1
TXD (serial output port)
P3.2
INT0 (external interrupt 0)
P3.3
INT1 (external interrupt 1)
P3.4
T0 (timer 0 external input)
P3.5
T1 (timer 1 external input)
P3.6
WR (external data memory write strobe)
P3.7
RD (external data memory read strobe)
Port 1
Port 1 is an 8-bit bi-directional I/O port with internal pullups.
The Port 1 output buffers can sink/source four TTL inputs.
When 1s are written to Port 1 pins they are pulled high by
the internal pullups and can be used as inputs. As inputs,
Port 1 pins that are externally being pulled low will source
current (I IL ) because of the internal pullups.
Port 1 also receives the low-order address bytes during
Flash programming and verification.
Port 3 also receives some control signals for Flash pro-
gramming and verification.
RST
Reset input. A high on this pin for two machine cycles while
the oscillator is running resets the device.
ALE/PROG
Address Latch Enable output pulse for latching the low byte
of the address during accesses to e xternal memory. This
pin is also the program pulse input (PROG) during Flash
programming.
In normal operation ALE is emitted at a constant rate of 1/6
the oscillator frequency, and may be used for external tim-
ing or clocking purposes. Note, however, that one ALE
Port 2
Port 2 is an 8-bit bi-directional I/O port with internal pullups.
The Port 2 output buffers can sink/source four TTL inputs.
When 1s are written to Port 2 pins they are pulled high by
the internal pullups and can be used as inputs. As inputs,
3
221378381.018.png
pulse is skipped during each access to external Data
Memory.
If desired, ALE operation can be disabled by setting bit 0 of
SFR location 8EH. With the bit set, ALE is active only dur-
ing a MOVX or MOVC instruction. Otherwise, the pin is
weakly pulled high. Setting the ALE-disable bit has no
effect if the microcontroller is in external execution mode.
unconnected while XTAL1 is driven as shown in Figure 2.
There are no requirements on the duty cycle of the external
clock signal, since the input to the internal clocking circuitry
is through a divide-by-two flip-flop, but minimum and maxi-
mum voltage high and low time specifications must be
observed.
Idle Mode
In idle mode, the CPU puts itself to sleep while all the on-
chip peripherals remain active. The mode is invoked by
software. The content of the on-chip RAM and all the spe-
cial functions registers remain unchanged during this
mode. The idle mode can be terminated by any enabled
interrupt or by a hardware reset.
It should be noted that when idle is terminated by a hard
ware reset, the device normally resumes program execu-
tion, from where it left off, up to two machine cycles before
the internal reset algorithm takes control. On-chip hardware
inhibits access to internal RAM in this event, but access to
the port pins is not inhibited. To eliminate the possibility of
an unexpected write to a port pin when Idle is terminated by
reset, the instruction following the one that invokes Idle
should not be one that writes to a port pin or to external
memory.
PSEN
Program Store Enable is the read strobe to external pro-
gram memory.
When the AT89 C51 is executing code from external pro-
gram memory, PSE N is ac tivated twice each machine
cycle, except that two PSEN activations are skipped during
each access to external data memory.
EA/VPP
External Access Enable. EA must be strapped to GND in
order to enable the device to fetch code from external pro-
gram memory locations starting at 0000H up t o F FFFH.
Note, however, that if lock bit 1 is programmed, EA will be
inte rnally latched on reset.
EA should be strapped to V CC for internal program
executions.
This pin also receives the 12-volt programming enable volt-
age (V PP ) during Flash programming, for parts that require
12-volt V PP .
Figure 1. Oscillator Connections
C2
XTAL2
XTAL1
Input to the inverting oscillator amplifier and input to the
internal clock operating circuit.
C1
XTAL1
XTAL2
Output from the inverting oscillator amplifier.
Oscillator Characteristics
XTAL1 and XTAL2 are the input and output, respectively,
of an inverting amplifier which can be configured for use as
an on-chip oscillator, as shown in Figure 1. Either a quartz
crystal or ceramic resonator may be used. To drive the
device from an external clock source, XTAL2 should be left
GND
Note: C1, C2 = 30 pF ± 10 pF for Crystals
= 40 pF ± 10 pF for Ceramic Resonators
Status of External Pins During Idle and Power-down Modes
Mode
Program Memory
ALE
PSEN
PORT0
PORT1
PORT2
PORT3
Idle
Internal
1
1
Data
Data
Data
Data
Idle
External
1
1
Float
Data
Address
Data
Power-down
Internal
0
0
Data
Data
Data
Data
Power-down
External
0
0
Float
Data
Data
Data
4
AT89C51
221378381.019.png 221378381.020.png 221378381.021.png
AT89C51
Figure 2. External Clock Drive Configuration
ters retain their values until the power-down mode is
terminated. The only exit from power-down is a hardware
reset. Reset redefines the SFRs but does not change the
on-chip RAM. The reset should not be activated before V CC
is restored to its normal operating level and must be held
active long enough to allow the oscillator to restart and
stabilize.
Power-down Mode
In the power-down mode, the oscillator is stopped, and the
instruction that invokes power-down is the last instruction
executed. The on-chip RAM and Special Function Regis-
Program Memory Lock Bits
On the chip are three lock bits which can be left unpro-
grammed (U) or can be programmed (P) to obtain the
additional features listed in the table below.
When lock bit 1 is programmed, the logic level at the EA pin
is sampled and latched during reset. If the device is pow-
ered up without a reset, the latch initializes to a random
value, and holds that value until r ese t is activated. It is nec-
essary that the latched value of EA be in agreement with
the current logic level at that pin in order for the device to
function properly.
Lock Bit Protection Modes
Program Lock Bits
LB1
LB2
LB3
Protection Type
1
U
U
U
No program lock features
2
P
U
U
MOVC instructions executed from external pro gram memory are disabled from
fetching code bytes from internal memory, EA is sampled and latched on reset,
and further programming of the Flash is disabled
3
P
P
U
Same as mode 2, also verify is disabled
4
P
P
P
Same as mode 3, also external execution is disabled
5
221378381.022.png
 

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin