bw-BU4200FCTC_DE_GB_FR.pdf
(
523 KB
)
Pobierz
Beiblatt zum Handbuch BU 4100
bzw. Betriebsanleitung BU 4200
NORDAC
vector mc
Frequenzumrichter
mit CAN Bus Anschluss
SK 250/1 FCTC ... SK 750/1 FCTC
SK 1100/1 FCTC ... SK 2200/1 FCTC
SK 750/3 FCTC ... SK 3000/3 FCTC
vector mc
vector mc
vector mc
vector mc
Control Box
mc
als Zubehr erhltlich
Allgemeines
Unterschied zur
Standard
vector mc
Frequenzumrichter:
Bei dieser Gerteausfhrung wurde die Standard RS485 Schnittstelle durch die CAN Bus
Schnittstelle (in/out) ersetzt. Daraus ergibt sich eine Vergr¦erung der Steuerklemmenanzahl von
18 auf 20.
Aufgrund der daraus resultierenden geringeren Abstnde vom Relais 2 zu den weiteren
Steuerklemmen, ist die zulssige Spannung an den Relais 2 Kontakten auf 28V begrenzt.
Das Relais 1 kann weiterhin mit bis zu 230V Wechselspannung genutzt werden.
Stand: Mrz 2002
Getriebebau NORD
GmbH & Co. KG
deutsch
NORDAC
vector mc
Beiblatt zu BU 4100/4200
2.8.6 Steueranschlsse, speziell fr
... FCTC
Gerte
Anschluss fr die Steuerleitungen:
- 20-polige Steuerklemmleiste, auf 2 Blcke verteilt
- 1,5 mm
2
fr Relais-Ausgnge (Block links)
Maximaler Anschlussquerschnitt:
- 1,0 mm
2
fr analoge und digitale Ein- und Ausgnge (Block rechts)
Kabel:
- getrennt von Netz-/Motorleitungen verlegen und abschirmen
Steuerspannungen:
- 5V, max. 400mA, auch zur Versorgung der optionalen
p-box
- 10V, max. 10mA, Referenzspannung fr ein Potentiometer
- 15V, max. 100mA, zur Speisung der dig. Eingnge
- analoger Ausgang 0 Î 10V, max. 5mA, fr ein ext. Anzeigegert
CAN Bus
Analog Ein-/Ausgang
Digitale Eingnge
1
2
3
4
ô
ô
ô
ô
-
+
1,8k
-
+
5
6
7
8
9
10
11
12
13
14
15
16
17
19
18
20
1
2
3
4
R
≈
5-10 k
Ω
oder von SPS Digital-
ausgnge (7.5 - 33 V),
gnd (Minus) auf
Klemme 6
Analogeingang
0 ... 10 V
(R
i
≈
14 k
Ω
)
Standardeinstellungen der
Relais Ausgnge (P434/441):
1-2: Bremsen- Steuerung
3-4: Bereitschaft (Strung)
CAN in
0/2...10 V bzw.
0/4...20 mA
(Beschaltung mit
Widerstand 250/500
Ω
an Klemme 7 und 8)
Standardeinstellungen der
Digitale Eingnge (P420-423):
1. EIN rechts
2. EIN links
3. Parametersatzumschaltung
4. Festfrequenz 1
CAN out
Hinweise
:
Alle Steuerspannungen beziehen sich auf ein gemeinsames Bezugspotential (GND, Klemme 6).
Dig. Eingnge
:
Der dig. Eingang 1 ist als schneller Eingang ausgelegt, Gesamtreaktionszeit ca. 1,2 ms.
Die sonstigen dig. Eingnge liegen bei etwa 6-10 ms.
Ausgangsrelais
:
*) max. zulssige Spannung zwischen den Klemmen 2 und 3 ist 230 V AC.
Leaflet supplementary to the BU 4100 Manual
and to the BU 4200 Operating Instructions
NORDAC
vector mc
Frequency Inverter
With CAN Bus Interface
SK 250/1 FCTC ... SK 750/1 FCTC
SK 1100/1 FCTC ... SK 2200/1 FCTC
SK 750/3 FCTC ... SK 3000/3 FCTC
vector mc
vector mc
vector mc
vector mc
Control Box
mc
available as an
accessory
General
The inverter configuration described here
differs from the
standard
vector mc
frequency inverter ...
... in that a CAN bus interface (with inputs/outputs) is substituted for the RS485 interface provided
as standard. With the CAN bus interface added to the inverter, the number of control terminals is
increased from 18 to 20. Due to the fact that relay 2 will be closer to the additional control terminals
as a result, a limit of 28V is defined for the contacts of relay 2.
As for relay 1, it may be exposed to an alternating voltage of up to 230V as with the RS485
interface.
Last updated: March 2002
Getriebebau NORD
GmbH & Co. KG
NORDAC
vector mc
BU 4100/4200 Supplement
English
2.8.6 Control terminal specification for
... FCTC
devices
Control wires to be connected to:
- a 20-pole control terminal strip, divided into 2 blocks
- 1.5 mm
2
for relay outputs (left block)
Maximum connection cross section:
- 1.0 mm
2
for analogue and digital inputs and outputs (right block)
Cables:
- to be laid separately from supply/motor leads and to be shielded
Control voltages:
- 5V, 400mA max., also for supply of the optional
p-box
(short-circuit-proof)
- 10V, 10mA max., reference voltage for a potentiometer
- 15V, 100mA max., to feed the digital inputs
- analogue output 0 Î 10V, 5mA, for an external display unit
analogue input / output
digital input
CAN bus
1
2
3
4
ô
ô
ô
ô
-
+
1,8k
-
+
5
6
7
8
9
10
11
12
13
14
15
16
19
20
17
18
1
2
3
4
R
≈
5-10 k
Ω
or from PLC
digital outputs
(7.5 - 33 V), GND (minus)
to terminal 6
analogue input
0 to 10 V
(R
i
≈
14 k
Ω
)
0/2 ... 10 V or
0/4 ... 20 mA
(resistor 250/500
Ω
to be connected to
terminals 7 and 8)
Default settings for the
relay outputs (P434/441):
1-2: brake control
3-4: ready for operation (fault)
CAN in
Default settings for the
digital inputs (P420-423):
1. enable right
2. enable left
3. change parameter set
4. fixed frequency 1
CAN out
Please note
:
All voltages are related to a common reference potential (GND, terminals 6).
Digital inputs
:
Digital input 1 is designed as a fast-reacting input with a total response time of approx. 1.2 ms.
The other digital inputs take about 6-10 ms to respond.
Output relays
*) Between control terminals 2 and 3 the maximum admissible voltage will be 230 V AC.
Feuille annexe au Manuel BU 4100
et la Notice d'emploi BU 4200
NORDAC
vector mc
Variateur de frquence
connexion de bus CAN
SK 250/1 FCTC ... SK 750/1 FCTC
SK 1100/1 FCTC ... SK 2200/1 FCTC
SK 750/3 FCTC ... SK 3000/3 FCTC
vector mc
vector mc
vector mc
vector mc
Control Box
mc
livrable comme
accessoire
Gnralits
A la diffrence du variateur de frquence
vector mc
standard
qui est muni d'une interface RS485, la configuration variateur traite dans la prsente feuille
d'information comporte une interface de bus CAN (E/S). Par suite de ce remplacement, le nombre
de bornes de commande total s'lve 20 (par rapport 18 quand l'interface RS485 est utilise).
Vu l'espacement plus rduit entre le relais 2 et les bornes de commande additionnelles, une
tension limite de 28V est dfinie pour les contacts du relais 2. Par contre, une tension alternative
de 230V est toujours permise pour l'exploitation du relais 1.
Etat de : mars 2002
Getriebebau NORD
GmbH & Co. KG
Plik z chomika:
luki2-82
Inne pliki z tego folderu:
tabliczki znamionowe do silników.pdf
(2044 KB)
Reduktory walcowo-ślimakowe -pozycja pracy.pdf
(318 KB)
Reduktory walcowe UNICASE -pozycja pracy.pdf
(191 KB)
Motor options 200-206.pdf
(419 KB)
I30_37.pdf
(680 KB)
Inne foldery tego chomika:
ABB kondensatory
ABS
Afriso
ALTER
APAREL
Zgłoś jeśli
naruszono regulamin