pcg-fx210.pdf

PCG-FX210

SERVICE MANUAL

US Model

Canadian Model

S400

NOTEBOOK COMPUTER

9-872-204-11

Information in this document is subject to change without notice.

Caution Markings for Lithium/Ion Battery - The following or similar

texts shall be provided on battery pack of equipment or in both the

operating and the service instructions.

Sony and VAIO are trademarks of Sony. Intel logo and Intel Inside

logo are registered trademarks of Intel Corporation. Pentium MMX

is a trademark of Intel Corporation. Microsoft, MS-DOS, Windows,

the Windows 95 and Windows 98 logo are trademarks of Microsoft

Corporation.

CAUTION: Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by

the manufacturer. Discard used batteries according to the

manufacturer’s instructions.

All other trademarks are trademarks or registered trademarks of

their respective owners. Other trademarks and trade names may be

used in this document to refer to the entitles claiming the marks and

names or their produces. Sony Corporation disclaims any proprietary

interest in trademarks and trade names other than its own.

CAUTION: The battery pack used in this device may present a fire

or chemical burn hazard if mistreated. Do not disassemble, heat

above 100°C (212°F) or incinerate.

Dispose of used battery promptly.

Keep away from children.

CAUTION: Changing the back up battery.

• Overcharging, short circuiting, reverse charging, multilation or

incineration of the cells must be avoided to prevent one or more of

the following occurrences; release of toxic materials, release of

hydrogen and/or oxygen gas, rise in surface temperature.

• If a cell has leaked or vented, it should be replaced immediately

while avoiding to touch it without any protection.

Service and Inspection Precautions

1. Obey precautionary markings and instructions

Labels and stamps on the cabinet, chassis, and components identify areas

requiring special precautions. Be sure to observe these precautions, as well

as all precautions listed in the operating manual and other associated

documents.

4. Inspect after completing service

After servicing, inspect to make sure that all screws, components, and wiring

have been returned to their original condition. Also check the area around

the repair location to ensure that repair work has caused no damage, and

confirm safety.

2. Use designated parts only

The set’s components possess important safety characteristics, such as

noncombustibility and the ability to tolerate large voltages. Be sure that

replacement parts possess the same safety characteristics as the originals.

Also remember that the 0 mark, which appears in circuit diagrams and

parts lists, denotes components that have particularly important safety

functions; be extra sure to use only the designated components.

5. When replacing chip components...

Never reuse components. Also remember that the negative side of tantalum

capacitors is easily damaged by heat.

6. When handling flexible print boards...

• The temperature of the soldering-iron tip should be about 270C.

• Do not apply the tip more than three times to the same pattern.

• Handle patterns with care; never apply force.

3. Always follow the original design when mounting

parts and routing wires

The original layout includes various safety features, such as inclusion of

insulating materials (tubes and tape) and the mounting of parts above the

printer board. In addition, internal wiring has been routed and clamped so

as to keep it away from hot or high-voltage parts. When mounting parts or

routing wires, therefore, be sure to duplicate the original layout.

Caution: Remember that hard disk drives are easily damaged by

vibration. Always handle with care.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT

CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE

REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY

DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU

DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

Confidential

PCG-FX210 (UC)

— 2 —

TABLE OF CONTENTS

Section

Title

Page

Section

Title

Page

CHAPTER 1. REMOVAL

1-1. Flowchart ......................................................................... 1-1

1-2. Main Electrical Parts Location Diagram ......................... 1-1

1-3. Removal ........................................................................... 1-2

1. Hood Keyboard Assy, Keyboard Unit .............................. 1-2

2. Cooling Unit-2, Lithium Battery, DVD-ROM Drive ....... 1-2

3. HDD, Door Battery .......................................................... 1-3

4. Palm Rest Assy, Touch Pad, CNX-129 Board,

Palm Rest Plate, Bracket Pad ........................................... 1-3

5. Display Assy, Hinge Cover .............................................. 1-4

6. PWS-14 Board, Latch Detector ...................................... 1-5

7. PC Card Connector, Modem Card, MBX-50 Board,

I/O Bracket ....................................................................... 1-5

8. Speaker Unit, SWX-74 Board ......................................... 1-6

9. SO-DIMM ........................................................................ 1-6

10. Modem Card (Removing from the bottom) ..................... 1-7

11. LCD Section – Made by AC – ......................................... 1-8

1. Bezel Housing Assy (14.1 inch) .................................. 1-8

2. Bracket LCD Left, Bracket LCD Right,

LCD Unit (14.1 inch) ................................................... 1-9

3. FPC, Inverter Assy, Display Housing Assy,

LCD Harness ................................................................ 1-9

1-4. Replacing the CPU ........................................................ 1-10

1. Removing the CPU ........................................................ 1-10

2. Installing the CPU .......................................................... 1-10

1-5. Replacing Various Connector on the MBX-50 Board ... 1-11

1. Removing the I/O Bracket ............................................. 1-11

2. Removing the Various Connectors ................................ 1-11

1-6. DIP Switch Setting of the MBX-50 Board .................... 1-12

(to 1-12)

CHAPTER 2. SELF DIAGNOSTICS .......................... 2-1

(to 2-1)

CHAPTER 3. BLOCK DIAGRAM ............................... 3-1

(to 3-2)

CHAPTER 4. FRAME HARNESS DIAGRAM ........ 4-1

(to 4-2)

CHAPTER 5. EXPLODED VIEWS AND

PARTS LIST ............................................ 5-1

5-1. Main Section .................................................................... 5-2

5-2. LCD Section – Made by AC – ......................................... 5-5

5-3. Connector Section ............................................................ 5-7

(to 5-8)

• Abbreviations

UC : US model / Canadian model

Confidential

— 3 —

PCG-FX210 (UC)

CHAPTER 1.

REMOVAL

1-1. Flowchart

CNX-129

BOARD

P 1-3

PALM REST

PLATE

BRACKET

PA D

TOUCH

PA D

P 1-3

HINGE

COVER

BEZEL

HOUSING

ASSY

LCD

UNIT

INVERTER

ASSY

DISPLAY

HOUSING

ASSY

P 1-4

P 1-8

P 1-9

DVD-ROM

DRIVE

DISPLAY

ASSY

P 1-2

P 1-4

LCD

HARNESS

LITHIUM

BATTERY

P 1-9

P 1-2

FPC

POWER

OFF

HOOD

KEYBOARD

ASSY

KEYBOARD

UNIT

P 1-2

DOOR

BATTERY

PALM REST

ASSY

LATCH

DETECTOR

PWS-14

BOARD

P 1-5

I/O

BRACKET

MBX-50

BOARD

P 1-9

P 1-2

P 1-3

P 1-5

SO-DIMM

SPEAKER

UNIT

PC CARD

CONNECTOR

MODEM

CARD

BRACKET

LCD LEFT

P 1-9

P 1-6

P 1-5

BATTERY

PAC K

SWX-74

BOARD

HDD

BRACKET

LCD RIGHT

P 1-6

P 1-3

P 1-9

FDD

COOLING

UNIT-2

P 1-2

MODEM

CARD

P 1-7

• P XX means pages that appears in this manual.

• Remember that hard disk drives are easily damaged by vibration. Always handle with care.

1-2. Main Electrical Parts Location Diagram

LCD Unit

Speaker Unit

Cooling Unit-2

Inverter Assy

HDD

SWX-74 Board

MBX-50 Board

Speaker Unit

CNX-129 Board

DVD-ROM Drive

PWS-14 Board

Modem Card

FD Drive

Touch Pad

Confidential

PCG-FX210 (UC)

1-1

1-3.Removal

1. Hood Keyboard Assy, Keyboard Unit

3 M2X4 Special Head (Black)

4 Pull it up sliding it to the right.

8 M2X4 Special Head (Black)

6 Hood Keyboard Assy

q; Keyboard Unit

Four Claws

MBX-50 Board

CON15

MBX-50 Board

CON21

2. Cooling Unit-2, Lithium Battery, DVD-ROM Drive

5 Rotate the three screws that are built together

with the Cooling Unit-2.

2 +B M2 (X2)

(Silver)

3 +B M2 (X2) (Silver)

5 Bracket CD-ROM R

7 DVD-ROM Drive

3 Plate ground

(SH)

4 +B M2 (X2)

(Silver)

MBX-50

Board CON4

7 Cooling Unit-2

Five Claws

9 +B M2 (Silver)

qa Lithium

Battery

2 Bracket (CD-ROM L)

1 +B M2 (X2) (Silver)

6 DVD-ROM Door Assy

MBX-50 Board

CON14

Lithium

Battery

Four

Claws

Confidential

PCG-FX210 (UC)

1-2

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: