Cabinets - Bathtub Enclosure.pdf

(74 KB) Pobierz
True Value.com
True Value.com
http://www.truevalue.com/content/Print/PrintPage.aspx?stage=2&id=11...
Build a Bathtub Enclosure
A bathtub enclosure frames your tub and creates a look of elegance and beauty.
Bathtub enclosures are a necessary finishing touch to a drop-in tub or a whirlpool tub. Installing one is
not as difficult as it looks. With a little skill and the right materials, anyone can build one.
Types and Sizes
The type of tub you have is important when building your enclosure. Drop-in bathtubs made
specifically for bathtub enclosures are the best to build around, but whirlpool bathtubs are also great
for building enclosures around. An enclosure is necessary to hide the water pipes on both drop-in and
whirlpool tubs. Make sure to work around the plumbing and the draining systems to avoid interfering
with pipes.
Tools and Materials You Need:
2 x 4 framing wood (amount depends on tub and how many frames needed)
Nails
Hammer
Saw (for wood cutting)
Construction adhesive
CDX plywood (or moisture resistant wallboard)
Caulk
Moisture resistant primer
Tile, wood, or other finishing material
Masking tape
1. Build a Tub Frame
Begin by framing your tub. Construct a frame out of 2 x 4 lumber for each side of the tub not
connected to the wall. Each side of the frame should consist of 2 pieces of wood the length of the side
it is adjacent to. The 2 long pieces are supported by 2 x 4 studs placed every 16 inches. The frame
should be about 3/4-inch below the rim of the tub, just enough for the plywood and tile to fit under the
rim. Nails the frames together and attach each frame to the wall and floor with nails and construction
adhesive.
Tip:
When cutting the studs that will support the horizontal 2 x 4s in the frame, remember to cut
off an extra 3 inches. These 3 inches will not be needed due to the height of the 2 vertical 2
x 4s.
1 of 2
11/05/2007 1:03 PM
112933717.017.png 112933717.018.png 112933717.019.png 112933717.020.png 112933717.001.png 112933717.002.png 112933717.003.png 112933717.004.png 112933717.005.png 112933717.006.png 112933717.007.png
True Value.com
http://www.truevalue.com/content/Print/PrintPage.aspx?stage=2&id=11...
2. Attach the Frame to the Wall and Floor
You can make your enclosure's ledge as wide as you want.
To extend your ledge on both sides, build a second frame a
few inches longer than the first and install it parallel to the
first frame. If you want your ledge to be wider than 16
inches, build a third frame. Anchor these additional
extensions to the wall and floor parallel to the previously
installed frame.
3. Cover and Seal the Frame
Attach 1/2-inch CDX plywood to the sides and tops of the frame with nails. As an alternative, you can
use a moisture resistant wallboard. Use caulk to seal all the joints between the bathtub and the covered
frame, and coat the wallboard or plywood with moisture resistant primer to seal it. Let the primer dry
completely.
4. Tile the Tub Enclosure
Using tile, wood or any finishing material, cover the plywood or wallboard once it is dry. Seal the
finishing material well with tile grout, and caulk all the joints to prevent water damage.
Tip:
To better understand installing tile or finishing material, see How To Install Ceramic Tile.
5. Caulk the Joints
Once the tile or finishing material has been caulked and dried, apply a layer of caulk around the
bathtub. Line all the tub edges with masking tape to make a straight line with the caulk. Apply the
caulk to the tub edges and smooth it with your finger. Let the caulk dry thoroughly and remove the
tape.
Tip:
When smoothing the caulk, put soap on your finger to make sure the caulk does not stick to
it.
2 of 2
11/05/2007 1:03 PM
112933717.008.png 112933717.009.png 112933717.010.png 112933717.011.png 112933717.012.png 112933717.013.png 112933717.014.png 112933717.015.png 112933717.016.png
Zgłoś jeśli naruszono regulamin