S7-300_FM350-2_e.pdf

Preface, Contents

Product Overview

SIMATIC

How the FM 350-2 Counts

Installing and Removing

the FM 350-2

FM 350-2 Counter Function

Module

Installation and Parameter

Assignment

Wiring the FM 350-2

Assigning Parameters

to the FM 350-2

Programming the FM 350-2

Manual

Starting Up the FM 350-2

Operating Modes, Settings,

Parameters, and Jobs

Encoder Signals and

Their Evaluation

DB Assignments

Faults and Diagnostics

Appendices

Technical Specifications

Spare Parts

Glossary, Index

Edition 12/2003

A5E00271805-01

Safety Guidelines

This manual contains notices intended to ensure personal safety, as well as to protect the products and

connected equipment against damage. These notices are highlighted by the symbols shown below and

graded according to severity by the following texts:

Danger

indicates that death, severe personal injury or substantial property damage will result if proper

precautions are not taken.

Warning

indicates that death, severe personal injury or substantial property damage can result if proper

precautions are not taken.

Caution

indicates that minor personal injury can result if proper precautions are not taken.

Caution

indicates that property damage can result if proper precautions are not taken.

Notice

draws your attention to particularly important information on the product, handling the product, or to a

particular part of the documentation.

Qualified Personnel

Only qualified personnel should be allowed to install and work on this equipment. Qualified persons

are defined as persons who are authorized to commission, to ground and to tag circuits, equipment, and

systems in accordance with established safety practices and standards.

Correct Usage

Note the following:

Warning

This device and its components may only be used for the applications described in the catalog or the

technical description, and only in connection with devices or components from other manufacturers

which have been approved or recommended by Siemens.

This product can only function correctly and safely if it is transported, stored, set up, and installed

correctly, and operated and maintained as recommended.

Trademarks

SIMATIC®, SIMATIC HMI® and SIMATIC NET® are registered trademarks of SIEMENS AG.

Third parties using for their own purposes any other names in this document which refer to trademarks

might infringe upon the rights of the trademark owners.

The reproduction, transmission or use of this document or its

contents is not permitted without express written authority.

Offenders will be liable for damages. All rights, including rights

created by patent grant or registration of a utility model or design,

are reserved.

Disclaimer of Liability

We have checked the contents of this manual for agreement with

the hardware and software described. Since deviations cannot be

precluded entirely, we cannot guarantee full agreement. However,

the data in this manual are reviewed regularly and any necessary

corrections included in subsequent editions. Suggestions for

improvement are welcomed.

Siemens AG

Bereich Automation and Drives

Geschaeftsgebiet Industrial Automation Systems

Postfach 4848, D- 90327 Nuernberg

©Siemens AG 2003

Technical data subject to change.

Siemens Aktiengesellschaft

A5E00271805-01

Preface

Purpose

This manual describes all the steps required for using the FM 350-2 function

module. It introduces you quickly and effectively to the functions of the FM 350-2.

Contents of This Manual

This manual describes the hardware and software of the FM 350-2. It consists of

an introductory section and a reference section (with Appendix).

The manual contains sections on the following topics:

Basic information on counting

Installation and expansion of the FM 350-2

Wiring the FM 350-2

Assigning parameters to the FM 350-2

Programming the FM 350-2

Appendix

Audience

The manual is aimed at the following readers:

Installation engineers

Programmers

Startup engineers

Service and maintenance personnel

Scope of This Manual

This manual contains the description of the FM 350-2 function module valid at the

time the manual was printed. We reserve the right to describe any subsequent

changes to the functions of the FM 350-2 in a Product Information.

Other References

You will find a list of other references on the topic of the S7-300 and programmable

controllers in the appendix.

FM 350-2 Counter Function Module

A5E00271805-01

Preface

Structure of This Manual

To make it easier for you to locate specific information, the manual has been

structured as follows:

At the beginning of the manual, you will find a complete table of contents for the

manual.

In the individual chapters, the information in the left margin gives an overview of

the contents of each section.

Following the appendices, there is a glossary containing definitions of the

important technical terms used in the manual.

At the end of the manual, you will find a detailed index giving you fast access to

the information you seek.

Standards

The S7-300 programmable controller conforms to the IEC 1131 standard.

Recycling and Disposal

The SIMATIC S7-300 is an environmentally friendly product. It is characterized by

the following points:

The plastic for the casing is coated with a halogen-free flame retardant despite

its high resistance to fire.

Labeling is done by laser (meaning no labels)

The plastics are coded according to DIN 54840

Fewer materials are used in this compact design, fewer components are

required as the result of integration in ASICs

The SIMATIC S7-300 can be recycled as a result of its minimal use of harmful

substances.

For environmentally compatible recycling and disposal of your old SIMATIC device

in accordance with the current state of the art, please contact:

Siemens AG

Anlagenbau und Technische Dienstleistungen

ATD TD 3 Kreislaufwirtschaft

Postfach 32 40

D–91050 Erlangen

Phone: (+49) 9131 / 7-33698

Fax: (+49) 9131 / 7-26643

This Siemens department provides a comprehensive and flexible disposal service

at a fixed cost with individual consultancy. You will be provided with papers

documenting the breaking down of your system giving details on the fractional

parts and the relevant verification papers for the materials.

CD–ROM

You can order a complete set of SIMATIC S7 documentation on CD-ROM.

FM 350-2 Counter Function Module

A5E00271805-01

Preface

Further Support

If you have any technical questions, please get in touch with your Siemens

representative or agent responsible.

You will find your contact person at:

http://www.siemens.com/automation/partner

Training Centers

Siemens offers a number of training courses to familiarize you with the SIMATIC

S7 automation system. Please contact your regional training center or our central

training center in D 90327 Nuremberg, Germany for details:

Telephone: +49 (911) 895-3200.

Internet: http://www.sitrain.com

FM 350-2 Counter Function Module

A5E00271805-01

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: