Creative Science & Research - High Efficiency Generator.pdf - !!Creative Science & Research Schematy DIY - WMatrixie

The

High Efficiency Generator

# HFG9

BLOCKER #1

BLOCKER #2

COIL with 1,000s of wraps #30 or #22

copper coated wire with soft iron core

or you can use Ductal # 65-4512

Use Very Powerful Ceramic Magnets, Horse Shoe or Bars

CREATIVE SCIENCE

& RESEARCH

P.O. BOX 557 NEW ALBANY, IN. 47150

(812) 945-5839

FREE ENERGY FROM A

COLLAPSING MAGNETIC FIELD!

Collecting the back EMF from a motor coil or generator coil. Back Emf is free energy from a collapsing magnetic field

generated in a coil of copper coated wire and collected to store or to apply back into the working apparatus or batteries.

So how do you collect the

back EMF?

Lets start with the basic's. We start with a coil of copper coated wire which is used as an electromagnet or a generator

coil. By applying 12 volts DC to the coil of wire you get a strong magnetic field, Polarity is forward and when that 12 vdc

is turned off the coil produces a reversed polarity, in which the magnetic field changes also. But voltage will be lower

because the 12 VDC must be pulsed (Switched on & off) at a high rate. The faster the better, So what is happening is you

are getting FREE ENERGY FROM A COLLAPSING MAGNETIC FIELD. SEE fig, #1 You will need to use a diode to

capture the back Emf.

The High Efficiency Generator # Hfg9

BLOCKER #1

BLOCKER #2

SMALL DC MOTOR

LOW AMPERAGE

HIGH EFFICIENCY TYPE

ROLLER BEARING

COIL with 1,000s of wraps #30 or #22

copper coated wire with soft iron core

or you can use Ductal # 65-4512

Use Very Powerful Ceramic Magnets, Horse Shoe or Bars

Blocker tops must be 1/8" or more

past the magnet on both sides.

also blockers must be no less than

3/16" thick, 1/4" is best.

Shaft

MAGNET AREA

FRONT VIEW OF BLOCKERS

AS CONNECTED ONTO SHAFT

HFG91.CDR

PAGE 1

The High Efficiency Generator # Hfg9

Or Try This Design

BLOCKER #1

BLOCKER #2

N S

Shaft Support

Bar

COIL with 1,000s of wraps #30 or #22

copper coated wire with soft iron core

or you can use Ductal # 65-4512

Very Powerful Ceramic Magnets, Bar Type stacked.

Suppliers

BAR MAGNET AREA

Ductal bar # 65-4512 ; Industrial Tube & Steel

1303 Home Ave

Akron, Ohio 44310

(213) 633-8125

Copper Coated Wire

Large Spools Of; Electrical Insulation

(502) 636-0384

Louisville, KY.

Magnets; Magnet Sales & Manf.

11248 playa court

Culver City, CA 90230

(800) 421-6692

PAGE 2

(800) 332-9567

The High Efficiency Generator # Hfg9

Blockers

Objective; To Make blockers and shaft as light weight as possible, To reduce

the resistance. (see front on plans Blocker #2 is pulled up in the

vertical position because of the magnet.

So if blocker #2 is being pulled into the vertical position by the north

and south poles of the magnet it is free energy helping to overcome

the lock position that #1 blocker is in. so there is two outside forces

helping the #1 blocker move out of the vertical lock position because

of blocker #1's magnet attracting to the iron in blocker #1 and that is

blocker #2 and the small hp dc motor.

Bar Magnet if you use this position

you can get the coil wider = more power.

ALUMINUM BAR

Iron Core

Iron core can be cut out or pieced together as

so; with the use of long bolts.

drill holes into center of core. Iron core can be

made of soft iron; laminated or solid.

another iron source to use is solid DUCTAL

# 65-4512 WHICH YOU CAN BUY AT; Industrial

Tubing & Steel 1-800-332-9567

Be sure to Paint core with enamel then Plastic

coat with solid type or liquid type you brush on.

it need not be to thick or to thin since we are

only using 12 volt to 120 volt ac.

PAGE 3

Creative Science & Research - High Efficiency Generator.pdf

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: