Canon - wheelloader.pdf

(3111 KB) Pobierz
loader_i_01e.pdf
Special Vehicle Series : 01
Wheel Loader
Assembly
Instructions
http://www.canon.com/c-park/en/
View of completed model
* This model was designed for Papercraft and
may differ from the original in some respects.
Tools
Assembly tip
Scissors
Ruler, set square
Glue (Wood glue or craft glue recommend)
Exhausted ballpoint pen (out of ink)
Toothpicks (for use in applying glue)
Tweezers (useful for handling small parts)
Pencil
Write the number of each part on the reverse side of the part in pencil
upon cutting it out, to be sure you can tell which part is which later.
Before gluing, crease the paper along
mountain and valley fold lines. Trace along
the folds with a ruler and an exhausted
ballpoint pen (out of ink) to get a sharper fold.
Make sure rounded sections are nice and stiff.
Key to symbols
Pattern
Assembly instructions
Dotted line
Mountain fold
Fold so that the printed
pattern faces outside.
The dots show where to glue
the pieces together. Glue the
pieces together as shown in the
following examples.
Some parts must be glued
together along the cut surfaces.
Red arrow
Glue
Blue arrow
Insert
Dashed and
dotted line
Valley fold
(without gluing)
Fold so that the printed
pattern faces inside.
Red dot
Light blue
Glue tab
Cut parts out
along this line.
Solid line
Glue parts with the same
number together. (Numbers are
not printed on very small parts.)
Reverse side of
paper
Light grey
Solid red line
Cut a notch
along this line.
Green dot
Movable part
Glue areas within the same
part together.
This denotes a part
that must be able to
move after the model
is completed. Be sure
to crease these parts
sufficiently.
Diagonal
grey lines
Cut these areas
out.
Blue dot
Glue to the reverse side of the
specified part.
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.
Assembly Instructions: Seven A4 sheets (No. 1 to No. 7)
Build this model with careful reference to the Assembly Instructions.
685039747.051.png 685039747.062.png 685039747.073.png 685039747.079.png 685039747.001.png 685039747.002.png
Wheel Loader
Assembly Instructions
Assemble the cab.
Glue flaps a and b in order.
Use care to get the shape right
when assembling this part,
referring to the cross section
at right.
Cross section
Close this surface last and glue it in place.
Glue flaps a, b, and c in order.
685039747.003.png 685039747.004.png 685039747.005.png 685039747.006.png 685039747.007.png 685039747.008.png 685039747.009.png
Wheel Loader
Assembly Instructions
Glue flaps a, b, c, d, and e
in order.
Leave an opening here.
Shape this part before gluing it.
This is a moving part.
Do not glue it.
Glue flaps a, b, and c in order.
Fold the left and right flaps
back and glue each in place.
Cross section
Glue to part G.
Use care to attach this part
in the right direction,
referring to the illustration.
Moving part
Moving part
Use care with the angles at which you glue parts
12 and 13 in place, to ensure the two parts are parallel.
Fold down the sides, then bend
the center down along the curved
edges and glue it in place.
Glue the back sides of the paper
parts together, in numbered order.
Fold in the ends of parts 22 and
28 and then glue them in place.
Reverse side
Cross section
Apply a small amount of
glue to the cut surface of
the paper as well, and glue
this part in place along
with the shape of the
bucket. (The bucket does
not have any glue tabs.)
Moving part
Glue parts 17 and 18 to
the reverse side of the bucket.
685039747.010.png 685039747.011.png 685039747.012.png 685039747.013.png 685039747.014.png 685039747.015.png 685039747.016.png 685039747.017.png 685039747.018.png 685039747.019.png 685039747.020.png 685039747.021.png 685039747.022.png 685039747.023.png 685039747.024.png 685039747.025.png 685039747.026.png 685039747.027.png 685039747.028.png 685039747.029.png 685039747.030.png 685039747.031.png 685039747.032.png 685039747.033.png 685039747.034.png 685039747.035.png 685039747.036.png 685039747.037.png 685039747.038.png 685039747.039.png 685039747.040.png 685039747.041.png 685039747.042.png 685039747.043.png 685039747.044.png 685039747.045.png 685039747.046.png 685039747.047.png 685039747.048.png
Wheel Loader
Assembly Instructions
Glue flaps a and b in order.
Insert into the opening
in part F.
Cross section
Referring to the cross section,
insert this part through the holes and
fix it in position at top and bottom.
Overhead view
Assemble in the same way as part 31.
This is the joint between
the front and rear sections.
685039747.049.png 685039747.050.png 685039747.052.png 685039747.053.png 685039747.054.png 685039747.055.png 685039747.056.png 685039747.057.png 685039747.058.png
Wheel Loader
Assembly Instructions
685039747.059.png 685039747.060.png 685039747.061.png 685039747.063.png 685039747.064.png 685039747.065.png 685039747.066.png 685039747.067.png 685039747.068.png 685039747.069.png 685039747.070.png 685039747.071.png 685039747.072.png 685039747.074.png 685039747.075.png 685039747.076.png 685039747.077.png 685039747.078.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin