6035 dress Instructions.pdf

PATTERN

A B 1 Front piece 1x

A B 2 Back piece 1x

A B 3 Center bust piece 4x

A B 4 Side bust piece 4x

A B 5 Center back piece 1x

A B 6 Side back piece 4x

A B 7 Shoulder strips 2x

B 8 Front wings 2x

B 9 Back wings 2x

B 10 Top hem inset 2x

B 11 Bottom hem inset 2x

How to lengthen and shorten pattern pieces: Cut the

pattern pieces along the marked lines

To lengthen , slide the two halves of the pattern piece as far

apart as necessary.

To shorten , overlap the two halves of the pattern piece as

far as necessary. Blend the side edges.

CUTTING OUT FOLD (– – – –) means: Cut on the fold, the

fold being the center of the pattern piece, but never a cut

edge or seam. The piece should be cut double, with the fold

line forming the center line. Pattern pieces that are outlined

with a broken line in the cutting diagrams are to be placed

face down on the fabric. The cutting diagrams on the pattern

sheet show how the pattern pieces should be placed on the

fabric.

Fabric: Light cotton and silk fabrics

Paper cut for ANSI A (German DIN A4) prints:

The patterns are printed out on 20 sheets with a thin frame.

Wait until all sheets are printed out. Arrange the

sheets so that they fit together (see additional page with the

overview of the prints). Fold the single sheets on

the upper and right edge along the thin frame lines. Begin

with the left lower sheet and then tape the frame

lines together precisely. Select your size according to the

Burda-dimension table: dresses, blouses, jackets

and coats according to the bust size, trousers and skirts

according to the hip width. Change the pattern to fit

your measurements if they deviate from the Burda-size

chart. Cut out the pattern 1 to 7 for the TOP A, pattern 1

to 11 for the TOP B; according to your size.

The cutting diagrams show the placement of the pattern

on the fabric. For a single layer of fabric, the pattern pieces

are pinned to the right side. For double layers of fabric, the

right sides are facing and the pattern pieces are pinned to

the wrong side. The pattern pieces that are shown extending

over the fold of the fabric in the cutting diagram should be

cut last from a single layer of fabric.

B fabric: Cut pieces 8 to 10 from the B contrasting fabric.

SEAM AND HEMLINE ALLOWANCES are included on an

average: 1 ½” (4 cm) for the hemline, 5/8” (1.5 cm) for all

edges and stitches. Using BURDA copying paper, transfer

the lines and signs of the pattern onto the wrong fabric side.

Instructions can be found in the packaging.

LENGTHENING OR SHORTENING THE PATTERN

PIECES Our pattern is calculated for a height of 5’ 6” (168

cm). If you are taller or shorter, you can adjust the pattern

pieces along the lines marked "lengthen or shorten here".

This way the proper fit is maintained. Always adjust all

pattern pieces along the same line to the same degree

SEWING

While sewing, the right sides of the fabric are facing.

Transfer all lines of the pattern onto the right side of the

fabric using basting stitches.

TOP

STRIPS

1 Fold the long edges of the strips to the center line,

then press. Fold the strip into half and press again. Pin

the edges together and stitch narrowly.

Top

Bust pieces (doubled)

2 Position the center bust pieces and the side bust

pieces together, right sides facing. Pin the princess

seams (seam 1) and stitch. Trim allowances, snip in

and press apart.

A Pin the strips on the upper edge of one left and one

right bust piece (2a), right sides facing.

3 Position the bust pieces together, right sides facing.

Position the neckline edges together according to the

image and stitch.

A Sandwich the strips

B Do not stitch at the arrow (arrow 3a), but continue

the seam to both sides.

Trim allowances, snip in. turn pieces. Pin the edges

and press. Pin the edges together.

4 Bring the pleats at the front piece in position as the

arrow shows, pin.

5 Pin the bust pieces on the front piece (seam 4), right

sides facing. the edges meet at the center front. Stitch.

Trim allowances, neaten and press.

BACK PIECE

6 Position together the two pairs of side back pieces,

right sides facing. Pin the top edges and stitch. Trim

allowances and press.

7 Position the side back pieces and the center back

piece, right sides facing. Pin princess seams (seam 2).

The seam meets the fold line. Trim allowances and

press.

8 Fold the center back piece along the FOLD LINE

inside and pin. Position the side back pieces together,

wrong sides facing. Pin the edges.

9 Position elastics on the center back piece. Stitch

over the elastics using narrow zigzag stitches. Make

sure not to stitch into the elastics. Then tighten the

elastics so that the back piece has a width of 8” (20

cm). knot the threads at the princess seams and sew

them down.

10 Position the top of the back piece on the bottom

back piece (seam 3), right sides facing. Stretch the

center piece. The princess seams meet the cross

lines. Stitch the seam. Trim allowances, neaten and

press.

HEM INSET

11 Position the top insets on the front and back

pieces (seam 5), right sides facing. Position the

bottom and top insets together and stitch (seam 6).

Neaten allowances and press.

SIDE SEAMS

Position the front piece on the back piece, right sides

facing. Pin side seams (seam 7). The cross lines

meet. Stitch. Trim allowances, neaten and press

inside the back piece.

12 Turn the HEM and press. Turn again and pin.

Topstitch the hem narrowly.

A Cross the strips. Pin the princess seams under the

back piece. Try the night gown on and adjust the

length of the strips according to your size. Sew the

strips by hand.

WINGS

14 Position the front and back wing pieces together,

right sides facing. Stitch the shoulder seams to the

cross line (seam 8). Secure seam ends. Trim

allowances, neaten and press. Turn the allowances

along the slit inside and press.

15 Stitch along the fold line using tightly adjusted

zigzag stitch. Trim the overlapping allowance close to

the seam line. ADVICE: Try it out using a fabric

scrap. Use machine thread or darning cotton. Check

stitch adjustment and thread tension. Snip it the front

wings ¼“ (0.7 cm) at the cross line (arrow 15a). Turn

and press the allowances of the outer wing edges

and neaten according to the text and image 15.

STRIPS

16 Pin the strips on the straight wing edges, right

sides facing; the ends overlap the cut ½” (1.5 cm)

(arrow). Stitch the strips ¼” (0.7 cm) wide. Press the

allowances inside the strip. Fold and press the other

edge ¼“ (0.7 cm).

17 Turn the strips over the edge inside, pin the strip

on the seam line and stitch narrowly.

18 Stitch the front ends of the strips on the bust

pieces, right sides facing. Neaten and press inside

the bust pieces. Stitch the cut edges on the strips

using a tight zigzag stitch (18a). Stitch the back strip

ends according to the text and image 13.

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: