apd100_e.pdf

WIRELESS PASSIVE INFRARED

DETECTOR

APD-100

apd100_e 08/05

The APD-100 wireless passive infrared detector is designed for operation as part of

the ABAX two-way wireless system.

The signal from pyroelement is

processed digitally. The sensor is

characterized by a high interference

immunity. The sensor detection

sensitivity is controlled by way of

radio.

The LED indicator is "on" in the

T EST MODE only (see the ACU-

100 controller manual) to signal

communication with the controller

and violation (of the detector or

tamper contact).

As two tamper contacts are

installed on the electronics

board, tamper information is sent

both when the housing is

opened, and when the detector is

pulled off from the mounting surface.

Placed on the electronics board is a label with 7-digit serial number, which must be

indicated when registering the detector in the system.

The detector is supplied from a CR123A 3V lithium battery, which ensures approx.

two years' operation.

battery

antenna

LED indicator

pyroelement

pull-off

tamper contact

housing

tamper contactt

positioning

scale

Fig. 1. Detector electronics board.

1. I NSTALLATION

Prior to permanent mounting of the detector, you should check the level of

signal received from the detector by the ACU-100 controller and, if necessary,

change place of the installation so as to ensure optimal positioning in terms of

communication.

The battery should be installed inside the detector just before registration of the

detector in the controller. If unregistered or missing communication with the

controller, the detector consumes more energy, which affects the battery life.

The detector is designed for indoor installation. It can be attached to the wall either

directly or mounted on a holder included in the delivery set. As the tamper contact

reacts to the pull-off, it is recommended that the device be secured directly to the wall

(one of the screws should be used to fix the housing tamper element). Before the

housing is mounted, remove the electronics board and make suitable screw holes in

the rear panel of the housing. Be particularly careful so as not to contaminate or

damage the pyroelement during installation.

SATEL

APD-100

The scale provided on the detector board (see Fig.1) is intended for properly setting the

pyroelement against the lens installed in the housing. If the detector is to be installed at

a height of 2.1m, set the board so that the central mark coincides with the indicator

placed on the housing next to the scale. Such a setting will ensure that the manufacturer

specified lens range is obtained. Otherwise, you should adjust the pyroelement setting by

moving the board up (if the detector is installed higher than 2.1m) or down (if the detector

is installed lower than 2.1m) as against its central position.

tamper element (to be

screwed to wall)

indicator to facilitate

positioning of

electronics board

Fig. 2. View of the detector housing rear panel.

For information on registering and installing the detector in the wireless system please

see the ACU-100 controller user manual.

2. L ENSES

Installed in the detector is an extra-wide lens (EWA), however it can be replaced with

another one, having different characteristics (range, number of beams, angle of view).

Lenses are available with the following specifications:

It.

Lens type

Range

Angle of view

1 extrawideangle

15m 141.2 °

long range with access zone

monitoring

30m main beam – 3m wide (at the end of range)

3 vertical barrier

22.5m 2.2m wide (at the end of range)

Note: The detector operating range should be selected to match the size of space

where the detector is to be installed. The size of the space along the main

direction of detector positioning is not to be less than 1/3 the nominal range of

the detector. Improper selection of the lens may cause excessive sensitivity

and trip false alarms.

APD-100

ABAX

TOP VIEW:

19.4°

10 m

5 m

10 m

SIDE VIEW:

2.1 m

1.7 m 4.6 m

7.7 m

15.3 m

Fig. 3. Distribution of beams and operating range of detector with extra wide angle (EWA)

lens.

SATEL

APD-100

3. T ECHNICAL DATA

Operating band frequency .......................................................... 868.0MHz ÷ 868.6MHz

Supply...................................................................................lithium battery CR123A, 3V

Life of detector battery............................................................................ approx. 2 years

Operating temperature range ....................................................................... 0°C...+55°C

Detectable movement speed......................................................................... up to 3 m/s

Housing dimensions .................................................................................. 63x96x49mm

Recommended height of installation ....................................................................... 2.1m

CAUTION

Batteries in the battery-supplied wireless equipment should be replaced by

qualified personnel. Incorrect replacement of the battery can pose an explosion

hazard.

Always use the CR123A 3V lithium batteries.

The used batteries must not be discarded, but should be disposed of in

accordance with the existing rules for environment protection.

DECLARATION OF CONFORMITY

Manufacturer: SATEL spółka z o.o.

ul. Schuberta 79

80-172 Gdańsk, POLAND

tel. (+48 58) 320-94-00

fax. (+48 58) 320-94-01

Product description : Wireless movement detector of PIR type, designed for interaction with

elements of the ABAX wireless system, operating in the 868.0MHz – 868.6MHz frequency band,

supplied from a 3V lithium cell. The device is intended to be used in burglary and panic alarm

systems.

This product conforms to the following EU Directives:

R&TTE 1999/5/EC

This product meets requirements of the harmonized standards:

R&TTE: ETSI EN 300 220-1: v.1.3.1; ETSI EN 300 220-3: v.1.1.1;

EMC: ETSI EN 301 489-1: v.1.5.1.; EN 301 489-3: v.1.4.1

Safety: EN60950-1:2001

Notified body taking part in conformity evaluation:

Identification No.: 1471

Gdańsk, Poland 2005-07-15

Head of Test Laboratory:

Michał Konarski

The latest EC declaration of conformity and product approval certificates are available for

downloading on our website www.satel.pl

Product:

APD-100 - Wireless PIR Detector for ABAX System

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: