BVS_manual_e.pdf

(3254 KB) Pobierz
388911517 UNPDF
Vision Sensor BVS
Operation Manual
English
388911517.012.png 388911517.013.png 388911517.014.png 388911517.015.png
Vision Sensor BVS Object Identification
388911517.001.png
Vision Sensor BVS Object Identification
1 Notes to the user
5
1.1 About this manual
5
1.2 Structure of the manual
5
1.3 Typographical conventions
5
1.4 Symbols
5
1.5 Abbreviations
5
2
General information
6
2.1 General description and Intended use
6
2.2 Components
6
2.3 Safety instructions
6
3
Getting Started - Installation
7
3.1 Sensor overview
7
3.2 Mounting
7
3.3 Electrical Connection
9
3.4 BVS ConVis Installation and start-up
9
3.4.1 Minimum system Requirements
9
3.4.2 BVS ConVis Installation
10
4
General Overview
11
5
BVS ConVis - Initial setup
12
5.1 Communicating with the sensor
12
5.1.1 Check PC Network Settings
12
5.1.2 Set up Communication
14
5.1.3 Troubleshooting
14
5.2 Recovery Mode
14
5.2.1 Entering Recovery Mode
14
5.2.2 Troubleshooting the sensor
15
5 5.3 Updating Software
15
5.5.4 Updating Firmware
16
6
Inspection Setup
17
6.1 General considerations
17
6.2 STEP 1: Image Setup
18
6.2.1 Quick Walkthrough STEP 1
18
6.2.2 Operations Modes
19
6.2.3 Establish Connection to Sensor – ONLINE MODE ONLY
19
6.2.4 Task Selection
20
6.2.5 Basic Setting – ONLINE MODE ONLY
22
6.2.6. Set Reference Image
22
6.3 STEP 2: TEACHING the application
23
6.3.1 Quick Walkthrough STEP 2
23
6.3.2 Select Trigger
25
6.3.3 Select Locator
25
6.3.4 Select Control
26
6.4 STEP 3: Run your Inspection
27
6.4.1 Quick Walkthrough STEP 3
27
6.4.2 Outputs Setup
28
6.4.3 Test
30
6.4.4 Run
31
6.5 Lighting Conditions Setup
32
6.5.1. Lightning Options
33
www.balluff.com
388911517.002.png 388911517.003.png 388911517.004.png
Vision Sensor BVS Object Identification
7
BVS CONVIS
34
7.1. Overview BVS components
34
7.1.1. Menu bar
34
7.1.2. Tool bar
36
7.1.3. Setup panel
37
7.1.4. Control Panel
37
7.1.5. Image Buffer
38
7.1.6 Work Area / Acquired image
39
7.1.7. Inspection Explorer
39
7.1.8 Help Panel
40
7.1.9 Status bar
40
7.2 Trigger
41
7.3 Locator
41
7.3.1. Usage of Locators
42
7.3.2 Selection and Positioning
43
7.3.3 Position Locator
44
7.3.4 Pattern Match Locator
47
7.4 Controls for the inspection
49
7.4.1 Choosing the approbriate Control
49
7.4.2 Multiple Controls in one Inspection
53
7.4.3 Selection and Positioning
53
7.4.4 Control parameters at the Inspection Explorer
54
7.4.5 Brightness
55
7.4.6 Contrast
56
7.4.7 Contour Match
57
7.4.8. Edge Count
59
7.4.9 Width
61
7.4.10 Pattern Match
63
7.4.11 Position
66
8
Periodic Maintenance
69
9
Legal Notices
70
10
Short Introduction to Machine Vision
71
10.1 Digital image
71
10.2 Machine vision
72
10.3 Binarization
72
10.4 Edge / Edge Detection
73
10.5 Inspection times
74
10.6 Contour match
74
10.7 Pattern match
75
10.8 Glossary
76
11
Technical Data
78
11.1 Dimensions
78
11.2 Specifications
78
11.3 Technical Data
79
11.4 LED Indicators
80
11.5 Select active Inspection via Digital Input
80
11.6 List of available Models
82
11.7 Declaration of Conformity
83
388911517.005.png 388911517.006.png
Vision Sensor BVS Object Identification
1
Notes to the user
1.1 About this
manual
This manual is intended as a quick-reference guide for the BVS Configuration and Visualisation
Software ( ConVis ) and the BVS Object Identification Vision Sensor.
1.2 Structure of the
manual
The manual is structured so that the sections are built sequential on one another
Section 1: General notes to the user
Section : General Information
Section : Getting Started - Installation
Section : General Overview
Section : BVS ConVis – Initial Setup
Section 6: Inspection Setup.
1.3 Typographical
conventions
Enumerations
The following conventions are used in this manual:
Enumerations are shown in list form with bullet points.
Entry 1,
Entry .
–
–
Actions
Action instructions are indicated by a preceding triangle. The result of an action is indicated by
an arrow.
Action instruction 1.
Action result.
Action instruction .
�
⇒
�
Syntax
Decimal numbers are shown without additional indicators (e.g. 1),
Hexadecimal numbers are shown with the additional indicator hex (e.g. 00 hex).
Parameters are shown in italics (e.g. CRC_16).
References to paths in which data are stored or are to be saved to are shown in small caps (e.g.
P roject :\D ata t yPes \U ser D efineD ).
Cross-references indicate where additional information on the topic can be found (see "Getting
Started" on page ) .
1.4 Symbols
Caution!
This symbol indicates a security notice which must be observed.
Note
This symbol indicates general notes.
Reference
This symbol indicates a reference to the Short Introduction to Machine Vision .
1.5 Abbreviations
BVS
Balluff Vision Sensor
EMC
Electromagnetic Compatibility
FOV
Field of View
IP
Internet Protocol
OI
Object Identification
ROI
Region of Interest
TCP
Transmission Control Protocol
Note
For other significant terms, please see the Glossary .
www.balluff.com
388911517.007.png 388911517.008.png 388911517.009.png 388911517.010.png 388911517.011.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin