XDieProductInstructions.pdf

X DIE

Patent # 5,635,661

PRODUCT INSTRUCTIONS

IMPORTANT: READ THIS SECTION FIRST

Before using the RCBS X-Sizer die, read this instruction manual care-

fully to fully learn how to safely operate the related reloading equipment.

Failure to properly operate certain reloading equipment can result in

severe personal injury and/or equipment damage. If you have read

these instructions, but do not clearly understand the described opera-

tion, call us at 1-800-533-5000 and a technician will assist you.

This instruction manual contains specific safety and operating information.

It should be considered a permanent part of your reloading equipment and

remain with the equipment at all times for easy reference.

SAFETY

Reloading is an enjoyable and rewarding hobby that can be con-

ducted safely. But, as with any hobby, carelessness or negligence

can make reloading hazardous. This product has been designed

from the beginning with the user’s safety in mind. When reloading,

safety rules must be followed. By observing these rules, the chance

of a hazardous occurrence causing personal injury or property dam-

age is minimized.

GENERAL

•

Use all equipment as the manufacturer recommends. Study

the instructions carefully and become thoroughly familiar

with the operation of the product. If you do not have written

instructions, request a copy from the equipment manufacturer.

•

Do not take short cuts. Attempting to bypass established

procedures is an invitation to an accident.

•

Observe “good housekeeping” in the reloading area. Keep

tools and components neat, clean and orderly. Promptly and

completely clean up primer and powder spills.

•

Reload only when you can give your undivided attention. Do

not reload when fatigued or ill, or under the influence of

medications or alcohol. Develop a reloading routine to avoid

mistakes which may prove hazardous. Do not rush - load at a

leisurely pace.

•

Always wear adequate eye protection to protect your eyes

from flying particles. You assume unnecessary risk when

reloading without wearing safety glasses.

LOADING DATA

•

Use only laboratory tested reloading data. We highly recom-

mend the SPEER reloading manual and the RCBS.load

reloading software.

•

OBSERVE ALL WARNINGS ABOUT THE USE OF MAXI-

MUM LISTED LOADS.

PRIMERS AND POWDER

•

Store primers and powder beyond the reach of children and

away from heat, dampness, open flames and electrical equip-

ment. Avoid areas where static electricity is evident.

•

Do not use primers of unknown identity. Scrap unknown

primers in accordance with applicable regulations.

•

Keep primers in the original factory container until ready to

use. Return unused primers to the same factory packaging for

safety and to preserve their identity. Primer packaging is

designed to provide safe storage.

•

DO NOT store primers in bulk. The blast of just a few hun-

dred primers is sufficient to cause serious injury to anyone

nearby.

•

DO NOT force primers. Use care in handling primers.

•

DO NOT have more than one can of powder on the bench at

one time. Powder cans should be stored away from the

bench to avoid picking up the wrong one.

•

DO NOT use any powder unless its identity is positively

known. The only positive identification is the manufact-

urer’s label on the original canister. Discard all mixed

powders and those of uncertain identity.

•

If you use a powder measure, replace the lids on both the

powder hopper and powder can after the powder hopper

has been filled.

•

When using a powder measure, settle the powder in the

powder hopper before charging any cases. Throw and check

the weight of at least ten charges. This will assure you that

the correct powder charge is being thrown.

•

When you finish a reloading session, pour any remaining

powder back into its original factory container. This will pre-

serve the identity and shelf life of the powder.

•

DO NOT smoke while reloading.

RECORD KEEPING

•

Keep complete records of reloads. Apply a descriptive label

to each box showing the date produced, and the primer,

powder and bullet used. Labels for this purpose are packed

with SPEER bullets. Never attempt to guess at the

identity of your ammunition.

Because RCBS has no control over the type and condition of fire-

arms used, components selected, assembly of those components

and the use of this product, we assume no responsibility, expressed

or implied, for the use of this product for reloading.

ABOUT THE X DIE

The X-Sizer die is a uniquely designed full length resizing die for

bottleneck rifle cases. This die not only full length resizes the

case, it also limits the growth of the case. This eliminates the

need for repeated trimming after an initial trim is done to stan-

dardize the case. This die is not intended to shorten the length of

the case, rather, as the case grows, the mandrel will reduce the

normal rate of growth. This is the result of the case mouth coming

in contact with the mandrel stop during resizing. Cases repeatedly

sized in the X-Sizer die will grow a few thousandths of an inch ini-

tially, and will then stabilize below the maximum case length.

Using the X-Sizer die eliminates the need to trim after each shot.

X-Sizer dies can be used for full-length resizing with or without

the X feature. Partial neck sizing can be done but only without

the X feature.

CLEANING THE X DIE

You MUST clean new dies before use. These dies contain a

small vent hole through which trapped air escapes during resiz-

ing. Sometimes the vent hole will plug up with factory polishing

material. This material will scratch and dent cases unless it is

removed. To clean, unscrew the mandrel from the die. Insert a

straightened paper clip, needle or similar object into the vent hole.

This will push the material into the die body. The debris can then

be easily removed by cleaning the inside of the die using a patch

saturated with OutersSolvent. Reassemble the die.

PREPARING YOUR CASES

All cases must be sized

and trimmed to the same

overall length. For the

best results, full-length

resize each case and trim

to .020” under maximum

case length. This is a

“one-time only” prepara-

tion of any and all cases to

be used in the X-Sizer die.

The X-Sizer die can be

used for full-length resizing

by setting it as follows:

• Install the proper shell

holder in the ram

Photo 1

• Adjust the mandrel so

the decapping pin extends

1/8” below

the die (see Photo 1).

• Screw the X-Sizer die

into the press until the die

touches the shell holder

when the shell holder is

brought up to the top of the

press stroke. To remove

any play in the press link-

age system, lower the shell

holder and adjust the die

1/8 to 1/4 of a turn down-

ward so the press cams

over center. Lower the press

handle all the way and note the “feel” of the cam over in the link-

age. With the handle all the way down, tighten the large die lock

ring.

• Insert a lubed case into the shell holder and run it into the die.

• Screw the mandrel into the die until hard resistance is felt.

• Back the mandrel out 1 to 2 turns and tighten the lock nut on

the mandrel.

• With this setting, lube and resize all the cases you plan to use

in the X-Sizer die. After sizing, remove the lube and trim the cases

as directed above.

Photo 2

X DIE SET UP

STEP 1: Back the

mandrel out of the die until the decapping pin extends below the

base of the die approximately 1/16” to1/8”. See photo 1.

STEP 2: Screw the X-Sizer die into the press until the die touch-

es the shell holder when the shell holder is brought up to the top

of the press stroke. To remove any play in the press linkage sys-

tem, lower the shell holder and adjust the die 1/8 to 1/4 of a turn

downward so the press cams over center. Make every effort possible

to duplicate the same amount of cam force each time the die is used.

See photo 2.

This product is covered by the RCBS Lifetime

Warranty. If you need a replacement part,

please call or write Customer Service

1-800-533-5000

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: