3391ch25.pdf

(312 KB) Pobierz
Microelectronics, Second Edition
25
Optical Storage
Systems
25.1 Introduction
.......................................
25 - 1
25.2 The Optical Head
..................................
25 -1
•
•
25.3 Worm Technology
.................................
25 -8
25.4 Magneto-Optic Technology
........................
25 - 8
25.5 Compact Disk-Recordable (CD-R)
.................
25 - 10
25.6 Optical Disk Systems
...............................
25 -12
Praveen Asthana
25.1 Introduction
Recordable optical disk drive technology provides a well-matched solution to the increasing demands for
removable storage. An optical disk drive provides, in a sense, infinite storage capabilities: Extra storage
space is easily acquired by using additional media cartridges (which are relatively inexpensive). Such
cost effective storage capabilities are welcome in storage-intensive modern computer applications such as
desktop publishing, computer aided design/computer aided manufacturing (CAD/CAM), or multimedia
authoring.
25.2 The Optical Head
The purposes of the optical head are to transmit the laser beam to the optical disk, focus the laser beam
to a diffraction limited spot, and to transmit readout signal information from the optical disk to the data
and servo-detectors.
The laser diode is a key component in optical storage, whether the recording technology is magneto-
optic, ablative WORM, or phase change. Early generations of optical drives used infrared lasers emitting
in the 780 nm or 830 nm wavelengths. Later generation of drives use red laser wavelengths emitting at
around 690 nm. The lasers are typically rated to have a maximum continuous output power in the 40-mW
range and are index guided to ensure good wavefront quality.
In a laser diode, light is emitted from the facets , which are the cleaved ends of the waveguide region of an
index guided laser. The facet dimensions are small enough (order of a few micrometers) for diffraction to
take place as light is emitted from the facet. As a result the output beam has a significant divergence angle.
In many commercial laser diodes, the width of the facet (i.e., the dimensions parallel to the pn-junction
plane) is much larger than the height (or the direction perpendicular to the junction plane), which causes
25 - 1
© 2006 by Taylor & Francis Group, LLC
752745991.004.png
25 -2
Microelectronics
LASER
DISK
LENS 1
COLLIMATING
LENS
DETECTOR
(POWER SERVO)
OBJECTIVE
LENS
CIRCULARIZER
BEAMSPLITTER
ASTIGMATIC
LENS
SERVO
DETECTOR
DATA
DETECTORS
FIGURE 25.1 Drawing of the optical head in a typical magneto-optic disk drive. Shown is a split-optics design, which
consists of a fixed set of components (the laser, detectors, and polarizing optics) and a movable system consisting of
a beam bender and an objective lens that focuses the light on the disk. ( Source: Asthana, P. 1994. Laser Focus World,
Jan., p. 75. Penwell Publishing Co., Nashua, N.H. Used by permission.)
the divergence angles to be unequal in the directions parallel and perpendicular to the laser junction. The
spatial profile of the laser beam some distance from the laser is thus elliptical.
The basic layout of the optical head of a magneto-optic drive is shown in Fig. 25.1. The laser is mounted
in a heat sink designed to achieve an athermal response. The output from the laser diode is collimated by
lens 1. A prismlike optical element called a circularizer is then used to reduce the ellipticity of the laser
beam. The beam then passes through a polarizing beamsplitter, which reflects part (30%) of the beam
toward a detector and transmits the rest toward the disk.
The output of the laser is linearly polarized in the direction parallel to the junction (which will be
referred to as P-polarization). The ratio of the intensity of the P-polarization component of the emitted
light to the ratio of the intensity in the S-polarization component is > 25:1. This polarizing beam splitter
is designed to transmit 70% of the P-polarized light and 100% of the S-polarized light. The light that is
reflected is incident on a light detector, which is part of a power servoloop designed to keep the laser at a
constant power. Without a power servoloop, the laser power will fluctuate with time as the laser junction
heats up, which can adversely affect the read performance.
The beam transmitted by the beam splitter travels to a turning (90 ◦ ) mirror, called a beam bender , which
is mounted on a movable actuator. During track seeking operations, this actuator can move radially across
the disk. The beam reflected by the turning mirror is incident on an objective lens (also mounted on the
actuator), which focuses the light on the disk. This type of optical head design in which the laser, the
detectors, and most of the optical components are stationary while the objective lens and beambender are
movable is called a split optics design . In early optical drive designs, the entire optical head was mounted
on a actuator and moved during seeking operations. This led to slow seek times (
∼
© 2006 by Taylor & Francis Group, LLC
200 ms) because of the
mass on the actuator. A split optics design, which is possible because coherent light can be made highly
collimated, lowers the mass on the actuator and thus allows much faster seek times.
The size of the focal spot formed by the objective lens on the disk depends on the numerical aperture
(NA) of the lens and the amount of overfill of the lens (i.e., the amount with which the diameter of the
incident collimated beam exceeds the aperture of the objective lens). The numerical aperture is given by
752745991.005.png
Optical Storage Systems
25 -3
θ max is the incidence angle of a light
ray focused through the margin of the lens. The beam of light incident on the objective lens usually has a
Gaussian electric field (or intensity) profile. The profile of the focused spot is a convolution of the incident
intensity profile and the aperture of the objective lens (Goodman, 1968). Overfilling the lens aperture
reduces the size of the focused spot at the cost of losing optical energy outside the aperture and increasing
the size of the side lobes. Optimization of the amount of overfill (Marchant, 1990) yields an approximate
spot diameter of
=
n sin
θ max ,inwhich n is the refractive index of the lens and
D
=
1
18
λ/
NA
(25.1)
is the wavelength of light and NA is the numerical aperture of the objective lens. The depth of
focus z of the focal spot is given by z
λ
( NA ) 2 .
The depth of focus defines the accuracy with which the objective lens position must be held with respect
to the disk surface. The smaller the depth of focus, the less tolerance the system has for media tilt and
the more difficult the job of the focus servosystem. Thus trying to reduce the spot size (always a goal as a
smaller spot allows a higher storage density) by increasing the NA of the lens becomes impractical beyond
an NA of about 0.6. The objective lens also acts as a collector lens for the light that is reflected from the
disk. This reflected light, used for the servosystems and during reading, contains the readout information.
The reflected light follows the incident path up to the fixed optical element. Beamsplitter 1 reflects all of
the S polarized light and 30% of the P polarized light in the direction of the servo and data detectors.
The portion of the light that is transmitted by the beamsplitter is, unfortunately, focused by the col-
limating lens back into the facet of the laser. This feedback light causes a number of problems in the
laser, even though the net amount of feedback does not exceed about 7% of the output light for most
magneto-optic media. Optical feedback affects the laser by causing the laser to mode hop randomly, which
results in a random amplitude fluctuation in the output. This amplitude noise can be a serious problem
and so techniques must be used to control the laser noise (such as injection of high-frequency current) or
HFM (Arimoto, 1986). Increasing the HFM current in general can decrease the amount of noise, but as
a practical matter, the injection current cannot be made arbitrarily large as it may then violate limits on
allowable radiation from computer accessories. Optical feedback also decreases the threshold and increases
the slope of the power-current (or PI) curve of the laser, but these effects are not really a problem.
The light reflected by beamsplitter 1 is further split by beamsplitter 2 into servo and data components.
The light reflected by the beamsplitter is incident on the data detectors. For magneto-optic read back,
two detectors are used in a technique known as differential detection (i.e., the difference in the signals
incident on the two detectors is taken). The light transmitted through beamsplitter 2 is incident onto a
special multielement servodetector and is used to generate the servosignals. The mechanism by which
these signals are generated are the subject of the following discussion on the servosystem .
=
0
8
λ/
The Servosystem
The servosystem is what enables the focused laser spot to be positioned with accuracy onto any of the
tracks on the disk and ensure that it can be moved to any track on the disk as required. The high track
densities (18,000 tracks/in) on optical disks require that the laser spot position be controlled to within a
fraction of a micrometer. To be able to move across the entire disk surface requires a large actuator, but
such an actuator will be too massive to quickly respond to the rapid changes in the track position (due to
run-out in the disk) as the disk spins. Therefore, a compound actuator consisting of a coarse actuator and
a fine actuator is used to control the radial position of the laser beam on the disk. The fine actuator, which
has a very low mass, can change the spot position rapidly over a limited range. The coarse actuator has a
slower response, but has a much wider range of motion and is used for long seek operations. Optical disks
have a continuous spiral groove (as in a phonograph record) to provide information on the relative track
location.
In addition to tracking and seeking, the laser spot in an optical drive must be kept in perfect focus on
the disk regardless of the motion of the disk (there can be quite a lot of vertical motion if the disk has tilt
© 2006 by Taylor & Francis Group, LLC
NA
.
in which
.
752745991.006.png
25 -4
Microelectronics
FINE
ACTUATOR
FROM
DETECTOR S
SENSOR
RESPONSE
TRACKING
CONTROL
COARSE
ACTUATOR
FOCUS
CONTROL
FOCUS
ACTUATOR
FIGURE 25.2 Block diagram of the servocontrol system for an optical disk drive.
or is slightly warped). To do this, the objective lens must be constantly adjusted to correct for the axial
motion of the disk surface as the media spins. The lens position is controlled by a focus servomechanism.
Figure 25.2 shows a block diagram of an optical drive servocontrol system (combined tracking and
focusing). The return beam contains information on the focus and position of the spot, which is processed
by the servo detectors. The feedback signals derived from the detectors allow the system to maintain control
of the beam.
The focus control system requires a feedback signal that accurately indicates the degree and direction of
focus error (Braat and Bouwhuis, 1978; Earman, 1982). To generate a focus error signal, an astigmatic lens
is used to focus onto a quadrant detector, a portion of the light reflected from the disk. In perfect focus, the
focalspotisequallydistributedon thefourelementsofthequaddetector(asshown inFig.25.3).However,if
the lens is not in focus, the focal spot on the detector is elliptical because of the optical properties of the astig-
matic lens. The unequal distribution of light on the detector quadrants generates a focus error signal (FES).
This signal is normalized with respect to light level to make it independent of laser power and disk reflec-
tivity. The focus actuator typically consists of an objective lens positioned by a small linear voice coil motor.
The coils are preferably mounted with the lens to reduce moving mass, while the permanent magnets are
stationary. The lens can be supported by either a bobbin on a sliding pin or elastic flexures. The critical fac-
tors in the design are range of motion, acceleration, freedom from resonances, and thermal considerations.
Once the spot is focused on the active surface, it must find and maintain position along the desired
track. This is the role of the tracking servo. The same quadrant detector that is used to generate the focus
signal can be used to generate the tracking error signal (TES). The beam returning from the disk contains
first-order diffraction components; their intensity depends on the position of the spot on the tracks and
varies the light falling along one axis of the quadrant detector. The TES is the normalized difference of the
current from the two halves of the detector, and it peaks when the spot passes over the cliff between a land
and groove (Mansuripur, 1987; Braat and Bouwhuis, 1978).
As a matter of terminology, the seek time usually refers to the actual move time of the actuator. The time
to get to data, however, is called the access time which includes the latency of the spinning disk in addition
A
B
A
B
A
B
FES =
( A − B ) + ( C − D )
A
+
B
+
C
+
D
C
D
C
D
C
D
(a)
(b)
(c)
FIGURE 25.3 Focus control system: (a) the quad detector, (b) the spot of light focused on the quad by the astigmatic
lens (circular implies objective lens is in focus), and (c) the spot of light on the quad when the objective lens is out of focus.
© 2006 by Taylor & Francis Group, LLC
752745991.007.png 752745991.001.png 752745991.002.png
Optical Storage Systems
25 -5
(60/3600)) s or
8 ms. Thus, a 3600-rpm drive with a seek time of 30 ms will have an access time of 38 ms. The standard
way to measure seek time is 1/3 of the full stroke of the actuator (i.e., the time it takes to cover 1/3 of the
disk). This is a historical artifact from the times of early hard disk drives.
The ability to accurately follow the radial and axial motions of the spinning disk results directly from
the quality of the focus and tracking actuators. To reject the errors due to shock, vibration, and media
runout, the servosystem must have high bandwidth. The limitation to achieving high bandwidth is usually
the resonance modes of the actuator. As the actuators are reduced in size, the frequencies of the resonances
become higher and the achievable bandwidth of the system rises. Servosystems in optical drives face
additional challenges because they have to handle removable media, which has variations between different
disks (such as media tilt).
×
Optical Recording and Read Channel
A schematic block diagram of the functions in an optical drive is shown in Fig. 25.4 . The SCSI controller
handles the flow of information to and from the host (including commands). The optical disk controller
is a key controller of the data path. It interprets the commands from the SCSI controller and channels data
appropriately through the buffer random access memory (RAM) to the write channel, or from the read
channel to the output. The drive control microprocessor unit controls, through the logic gate arrays, all
the functions of the optical drive including the servo control, spindle motor, actuators, laser driver, etc.
Data that are input to the drive over the SCSI for recording are first broken up into fixed block sizes (of,
for example, 512 kilobyte or 1024 kilobytes length) and then stored in the data buffer RAM. Magneto-optic,
phase-change, and WORM drives can be classified as fixed block architecture technologies in which data
blocks are recorded much like in hard drives (Marchant, 1990). Blocks of data can be placed anywhere on
the disk in any sequence. The current CD recordable drive is, on the other hand, an example of a non-fixed
block architecture (because its roots are in CD audio). In common CD-R drives, input data are recorded
sequentially (like a tape player) and can be of any continuous length.
Error correction and control ( ECC ) bytes are added to each block of data. Optical drives use Reed–
Solomon codes, which are able to reduce the error rate from 1E-5 to about 1E-13 (Golomb, 1986). After
the addition of ECC information, the data are encoded with run length limited (RLL) modulation codes
(Tarzaiski, 1983; Treves and Bloomberg, 1986) in order to increase efficiency and improve detection.
Special characters are inserted in the bit stream such as a synchronization character to tell where the data
begins. All in all, the overhead required to store customer data is about 20%.
In most current optical drives, recording is based on pulse position modulation ( PPM ) techniques.
In basic PPM recording, the presence of a mark signifies a one and the absence signifies a zero bit. Thus,
a 1001 bit sequence would be recorded as mark-space-space-mark. In pulse width modulation (PWM)
recording, the edges of the mark represent the one bits (Sukeda et al., 1987). Thus a 1001 bit sequence
would be recorded as a single mark of a certain size. A longer bit sequence such as 100001 would be
represented by a longer mark, hence the term pulse width modulation. The use of pulse width modulation
allows a higher linear density of recording than pulse position modulation.
A comparison of PWM recording with the current technique of PPM is shown in Fig. 25.5 . It is more
difficult to implement PWM technology (a more complicated channel is required), and PWM writing has
greater sensitivity to thermal effects. Thus implementing PWM is a challenging task for drive vendors.
On readback, the light reflects from the disk and travels to a photodetector (or two detectors in the case
of magneto-optic drives). For WORM, phase-change, and CD-R disks, the signal is intensity modulated
and thus can be converted to current from the detectors and amplified prior to processing. The WORM,
phase-change, and CD-R disks have a high contrast ratio between mark and no-mark on the disk and thus
provide a good signal-to-noise ratio. In magneto-optic drives, the read signal reflected off the disk is not
intensity modulated but polarization modulated. Thus polarization optics and the technique of differential
detection must be used to convert the polarization modulation to intensity modulation (as is discussed
later in the section on magneto-optic recording).
© 2006 by Taylor & Francis Group, LLC
to the seek time. For example, a drive spinning a disk at 3600 rpm has a latency of (0.5
752745991.003.png
Zgłoś jeśli naruszono regulamin